主要按照下面文档进行安装的：

http://wenku.baidu.com/view/462ab595dd88d0d233d46ac6.html

文档转帖见其他文章

安装MC程序

install mc service guard（swinstall）

激活节点1上所有卷vgchange -a y /dev/vgdb0 /dev/vglock

生成MC配置文件

cmquerycl -v -C /etc/cmcluster/cmclconf.ascii -n RX660059 -n RX660071

----------------------------------

vi /etc/cmcluster/cmclconf.ascii，修改必要信息

CLUSTER_NAME cluster1

FIRST_CLUSTER_LOCK_VG /dev/vglock

NODE_NAME RX660059

NETWORK_INTERFACE lan0

HEARTBEAT_IP 15.154.146.59

NETWORK_INTERFACE lan1

HEARTBEAT_IP 192.168.1.59

FIRST_CLUSTER_LOCK_PV /dev/dsk/c1t0d1

NODE_NAME RX660071

NETWORK_INTERFACE lan0

HEARTBEAT_IP 15.154.146.71

NETWORK_INTERFACE lan1

HEARTBEAT_IP 192.168.1.71

FIRST_CLUSTER_LOCK_PV /dev/dsk/c1t0d1

HEARTBEAT_INTERVAL 1000000

NODE_TIMEOUT 2000000

AUTO_START_TIMEOUT 600000000

NETWORK_POLLING_INTERVAL 2000000

NETWORK_FAILURE_DETECTION INOUT

MAX_CONFIGURED_PACKAGES 10

VOLUME_GROUP /dev/vgdb0

VOLUME_GROUP /dev/vglock

----------------------------------------------

cmcheckconf -v -C /etc/cmcluster/cmclconf.ascii （检测该文件是否正确，如果没有显示错误err，那么检测通过）

vgchange -a y /dev/vglock，再次激活vglock卷组

cmapplyconf -v -C /etc/cmcluster/cmclconf.ascii，将双机信息分发到各节点上

cmcheckconf -v -C /etc/cmcluster/cmclconf.ascii，再次检测

vi /etc/rc.config.d/cmcluster, 修改为AUTOSTART_CMCLD=1 (将MC程序设置成自启动，两个node都需要修改)

cmruncl -v，启动双机

cmviewcl -v，查看双机信息

至此双机程序安装完毕，下面开始安装双机中的包。

mkdir /etc/cmcluster/pkg

cmmakepkg -p /etc/cmcluster/pkg/ora.conf

vi /etc/cmcluster/pkg/ora.conf

ora.conf文件见其他文章

cmmakepkg -s /etc/cmcluster/pkg/ora.sh

vi /etc/cmcluster/pkg/ora.sh

ora.sh文件见其他文章

mkdir /etc/cmcluster/pkg，在71上创建一个文件夹

将建好的配置文件和shell文件分发到其他节点

rcp /etc/cmcluster/pkg/ora.sh RX660071:/etc/cmcluster/pkg/ora.sh

rcp /etc/cmcluster/pkg/ora.conf RX660071:/etc/cmcluster/pkg/ora.conf

cmcheckconf -v -C /etc/cmcluster/cmclconf.ascii -P /etc/cmcluster/pkg/ora.conf

cmapplyconf -v -C /etc/cmcluster/cmclconf.ascii -P /etc/cmcluster/pkg/ora.conf，重新分发文件

修改oracle10g.sh，模板见oracle10g.sh，并分发到其他节点

rcp /etc/cmcluster/pkg/oracle10g.sh RX660071:/etc/cmcluster/pkg/oracle10g.sh

oracle10g.sh文档见其他文章

按照正常流程安装数据库

修改监听文件内容，监听的名字，注意监听中的HOST不能改为浮动IP，否则客户端无法登录，把适合本机的监听文件放到/etc/cmcluster/ora/listener.ora